WiFi bridge kit – Wireless Point to Point Link
The Best COMPLETE WiFi bridge solution on the market
Finally! A complete WiFi bridge kit, fully configured.. Mount the hardware, plug in the power, and you’re set! No more programming nightmares, we do it all for you!* RadioLabs Bridge in a box, high power, long range wireless bridge system. Create a very fast, 150 MBPS wireless bridge link, instantly.
RadioLabs, the long time leader in personalized wireless networking, is proud to offer our customers, a completely programmed bridge kit, with nothing else to do except mount the hardware and connect to your router or AP. This kit, will combine 2 network systems, or, can act as the center hub for an entire wireless networking link, to provide your own independent cable company or DSL drop, to your home, up to 5 miles guaranteed in a rural situation.
At RadioLabs, we’ve been manufacturing and selling our own brand WiFi bridge systems since 2002. We were one of the first companies in the world, building bridge systems for rural homes, residential customers as well as large brand name corporations. We’ve been in this business and we know what it takes. When we advertise 5 miles, we use specific tools to know that our bridge systems don’t just go 5 miles barely, we ensure that our systems not only make the distance, but there is substantial overhead to ensure you have the speed and wireless receiver/transmitter margin to obtain the best signal possible. Our wireless bridge firmware, as well as the chipsets we use, give you the best wireless connectivity possible. This leve of performance is not cheap. We work with the top wireless companies in the world, to give you the highest level of performance possible from every single chip on board. Our o2Surf’s specifications are just incredible and this truly shows in each and every WiFi bridge we’ve ever sold.
Need a fast wireless bridge? Try RadioLabs GS-3000 or GS-5000, MiMo Wireless Bridge, allowing 300 MBPS Speeds on 2.4 or the entire 5 to 6 GHz range!
Note: RadioLabs recognizes that networking bandwidth requirements are ever increasing, and that older 802.11G WiFi Network bridging speeds don’t cut it. With this combination kit of high power equipment, you can easily obtain wireless speeds of up to 150Mbps Wireless bridging for point to point links, up to and exceeding 5 miles. (line of sight, interference and obstructions will limit bridge distances)
Long Range High Speed Wifi Bridging System
A full featured, low cost, point to point wireless bridge kit, containing everything needed to link two locations with wireless speeds up to 150 megabits/second. When reliability, range and cost are your #1 goal. We specialize in bridges. Our company lives off of one. Our 2.4 Ghz, O2Surf bridge, is the best performing wireless bridge system on the market, guaranteed.
RadioLabs has been selling this bridge kit, or, a different version of this bridge kit, for over a year, and it’s been one of the most successful products in our inventory. The o2Surf Wireless multi-purpose WiFi radios are ultra stable, very sensitive, programmable system, capable of performing any Wireless Mode, including Access Point, Router, Client, WDS Bridge or Repeater mode and they have been flawless!
Utilizing our new O2 Surf radios, this wireless bridge is the ultimate WiFi solution for when internet is required in remote locations. Coupled with a 15db Backfire WiFi Antenna, the O2 Surf High Speed Wifi Bridging System provides wireless speed/wireless/wifi-antennas/directional-wifi-antennas/backfire-2-4-ghz-wifi-antenna/s of up to 150Mbps, which allows for seamless streaming of HD video, Skype video calls or other VOIP traffic, and blazing fast downloads.
Outdoor Wireless Bridge Radios – High Performance WiFi
RadioLabs oSurf Multi-mode WiFi bridge radios, performs all of the magic in many of our wireless applications. This compact, weatherproof, multi-functional unit is capable of operating as a transparent wireless bridge, an AP, client, or repeater. Powered by a POE (Power-Over-Ethernet), you don’t even need to run a power supply to the bridge, just use the included power injector and your bridge has power and data transmitted over CAT-5 cabling. Moreover, due to the O2 Surf being able to connect directly to the Backfire Antennas, consumers can rest assured that their system will operate with minimal (if any) signal loss and degradation.
Setup is accomplished through a web interface using a standard web browser, similar to the set up of your typical wireless router. Integrating this bridge system into an existing network is extremely simple, with ease of access and remote management capabilities.
WiFi Bridge – With Long Range Wireless Bridge Radios
The O2 Surf’s 600mW transmit power combined with the Backfire WiFi Antenna’s 15dB of transmit gain allows line-of-sight links of multiple miles at substantially increased bandwidth capacity. The POE capabilities of the O2Surf allow flexibility in placement of the bridge devices. Supporting Cat-5 cable lengths up to 150 feet, the individual radio/antenna combinations can be easily located where the clearest line of sight between the two points is possible.
This compact bridging system can be used to extend an existing network to a remote location, share an internet connection, and with the addition of a wireless router or access point (such as the One Watt O2 Breeze 802.11 b/g/n Wireless Router), a separate wireless network can be created at the remote end of the link. The versatility of the O2 Surf High Speed Bridging System provides a wide range of uses and can provide high speed connectivity in a multitude of applications.
WiFi Bridge Configuration:
The configuration on the O2Surf Bridge in a box kit, is to: 192.168.1.20, and 192.168.1.21. The default gateway is set to 192.168.1.1, because we cannot predict the gateway of your router’s IP. This is a very easy setting, and generally, the issue automatically resolves itself. In the rare event this setting doesn’t automatically adjust itself, a quick trip to our remote support server will fix this fast, while you sit back and enjoy watching our techs do the work.
If you would like us to configure this to a completely different network, please contact us for more information.
Programming on the O2Surf, high power bridge kit, is to our standard manual. It requires a lot of technical time, so please give us 24 – 48 hours on custom bridge configurations.
*IMPORTANT: If you want to change the base IP address on the bridge kit, please call one of our technicians during or after placing the order (within 6 hours of placing it) and we can custom configure it. If there is additional programming for custom IPs or VLAN gateway, there could be an additional charge, so please check with us first)
We guarantee it’s connected to your network, or you can log in to our remote tech support server and we will finish the bridge for you!