N Male Connector – Wifi – Wireless cable

$4.25

N Male Connector for RL or LMR 400 coax. These rugged connectors are crimp style, ultra low-loss design, incorporating a gold plated pin, crimp ring, and allow for wrench or finger tightening to any coax, or wifi / wireless radio. Perfect for all outdoor applications, which require N Male connection. Works on all RadioLabs WiFi Antennas.

RP-SMA Female – WiFi Coax Connector | 100-400

$4.00$4.25

RP-SMA Connector for RL-LMR-400 and 100 style coax. These high quality, crimp style connectors are the highest quality available, made of solid metal, plated, with gold plated center conductor pin. These connectors are the same style we have used for over a decade, on thousands of customer bridges, omni antennas and almost any imaginable WiFi – Wireless installation.

RP-SMA Male – WiFi Connector for RL-LMR 400 Cable

$4.00$4.25

RadioLabs high quality RP-SMA Male WiFi coaxial connectors, crimp style, for all RL and LMR-400 and 100 series cable. We have installed tens of thousands of these connectors since 2001. They are the most common WiFi connectors on the market, fitting most routers. Install onto any cable with proper crimping tool in seconds. Center solder to tip, or, crimp to tip instantly. We recommend soldering on tip, crimp to braid on outside. Available in single qty, 10 and 100 bulk pack.

WiFi Pigtail Coax Cables – Wireless Pigtails

$14.95

WiFi Pigtail cables – The perfect solution for adapting any wireless card, access point, router or wireless network device to a universal coaxial cable. RadioLabs offers 12″ pigtails for connection to your wireless product. Wifi pigtails are a common way of adapting any wifi device or different cable diameter by adding flexibility to your wifi or wireless cables. AP, Antenna, etc The wifi pigtails are made with high quality coaxial cable (LMR-100 or RG-316 or Equiv) connectors, for simply adapting N Female or N Male to your wireless card, amplifier or injector.

WiFi- Wireless Coax Cable- RL-LMR-400

$22.95$115.95

RadioLabs WiFi Antenna Cable

RadioLabs’ Custom made Coaxial cable is one of the most important, and often overlooked aspects of any WiFi installation. RadioLabs RL-400 cable, combined with the connector you need, provide the ultimate in low-loss WiFi for 2.4 or the “lossy” 5-6 Ghz band. RadioLabs’ technicians, cut, solder and crimp your coaxial cable, solder, then use high end hydraulic crimp tooling, along with heat shrink, to the exact length you require. Our low-loss cable, is 0.400″ diameter for the lowest loss cable in the industry. Identify the connector you need, or ask for assistance if required. All RadioLabs’ coax cables will have an N Male connector on one end, unless you call to specify a custom connector on that end. We have built hundreds of thousands of feet of WiFi cable over the years, to our customer’s requirements. Ask for volume pricing.

Wireless – WiFi Coax Cable – RL-LMR-400 Low Loss

$74.95$534.95

WiFi – Wireless – RL-LMR-400 series cables, RadioLabs ultra low-loss cable is a very high quality, low loss coaxial cable for all RF Applications, but specifically designed for the best possible specifications you can achieve in the 2.4 and 5.8 Ghz wireless band. RadioLabs unique RL-LMR-400 has lower loss than competitor’s cable, because it was designed using specialized materials, and center conductor / RF Foil and dense, yet flexible 100 percent shielding. Of all wide range cables available on the market, RadioLabs RL-400 and LMR-400 coax is the lowest loss available before switching to small diameter hard line.

Showing all 8 results